Device matrix

Which board_config serves which product board, and what each one exposes under the board peripherals contract: eager UI in board_config.py, lazy extras in board_peripherals.py (PERIPHERALS).

For panel, touch controller, and bring-up quirks on these boards, see display-boards.md.

Paths below are relative to board_configs/ and are MicroPython trees (the ones with board_peripherals). CircuitPython twins under cp/ are eager-UI only (display_drv / app / touch / keypad / encoder / joystick) — they have no lazy PERIPHERALS; use native board for the rest.

display_drv / app / display_bus are always part of the board surface when present, and are omitted from the Eager column for brevity.

---

Panel-first boards

Boards whose display is the reason to buy them.

Product	board_config path	Eager UI	Lazy PERIPHERALS
Waveshare ESP32-P4-WIFI6-Touch-LCD-4B	fbdisplay/esp32-p4-wifi6-touch-lcd-4b	touch	audio_out, audio_in, sdcard, camera, radio, wlan, ble, usb_device
Adafruit Qualia S3 + TL040HDS20	fbdisplay/qualia_tl040hds20	touch, keypad, io_expander	wlan, ble
Waveshare ESP32-S3-Touch-LCD-4.3	fbdisplay/esp32-s3-touch-lcd-4_3	touch, io_expander	sdcard, can, rs485, usb_device, wlan, ble
Waveshare ESP32-S3-Touch-LCD-7	fbdisplay/esp32-s3-touch-lcd-7	touch, io_expander	sdcard, can, rs485, usb_device, wlan, ble
LILYGO T-RGB 2.1″	fbdisplay/t-rgb_480	touch	sdcard, battery, wlan, ble
LILYGO T-Embed	busdisplay/spi/t-embed	encoder	pixels, audio_out, audio_in, sdcard, battery, i2c, wlan, ble
LILYGO T-HMI	busdisplay/i80/t-hmi	touch	sdcard, i2c, wlan, ble
Waveshare RP2040-Touch-LCD-1.28	busdisplay/spi/rp2040-touch-lcd-1.28	touch	accelerometer, gyroscope, battery
Adafruit Metro M7 + TFT shield 1947	busdisplay/spi/metro_m7_tft_touch_shield_1947	touch	pixels, led, sdcard, radio, wlan, i2c
ST NUCLEO-H743ZI2 + TFT shield 1947	busdisplay/spi/nucleo_h743zi2_tft_touch_shield_1947	touch	led, sdcard, ethernet

The ESP32-P4 WIFI6-Touch-LCD-4B has no ethernet PHY (ETH is a different SKU); camera stays in PERIPHERALS as a CSI stub.

---

Sensor-rich and general boards

All rows have board_peripherals.py unless noted. Some factories still raise NotImplementedError until the chip drivers land — the PERIPHERALS set is the contract surface, not a completeness guarantee.

Product	board_config path (MP)	Eager UI	Lazy PERIPHERALS	Notes
Adafruit FunHouse	busdisplay/spi/funhouse	touch, keypad	temperature, humidity, pressure, pixels, audio_out, wlan	no BLE on ESP32-S2
Adafruit PyGamer	busdisplay/spi/pygamer	joystick, keypad	pixels, accelerometer, sdcard, battery, audio_out, i2c
Adafruit Feather RP2040 + RGB matrix wing	fbdisplay/feather_rp2040_rgb_matrix_64x32	—	i2c	matrix is display_drv
Adafruit Feather RP2040 DVI	fbdisplay/adafruit_feather_rp2040_dvi_320x240	—	—	MP stub raises NotImplementedError (SRAM); CP POC under cp/fbdisplay/adafruit_feather_rp2040_dvi_320x240
Teensy 4.1 + FlexIO ILI9341	busdisplay/i80/teensy41_flexio_ili9341	—	(empty)	split layout; no onboard lazy extras
Teensy 4.1 + RGB matrix featherwing	fbdisplay/rgb_matrix_featherwing_teensy41_64x32	—	(empty)
Adafruit PyBadge	busdisplay/spi/pybadge	keypad	pixels, accelerometer, audio_out, i2c
Adafruit PyPortal	busdisplay/spi/pyportal	touch	sdcard, radio, audio_out, i2c, wlan	AirLift as radio/wlan
Adafruit PyPortal Titano	busdisplay/spi/pyportal_titano	touch	sdcard, radio, audio_out, i2c, wlan
Adafruit HalloWing M4	busdisplay/spi/hallowing_m4	—	pixels, accelerometer, audio_out, i2c
ODROID-GO	busdisplay/spi/odroid_go	joystick, keypad	battery, sdcard, audio_out, wlan
M5Stack CoreS3	busdisplay/spi/m5stack-cores3	touch	audio_in, audio_out, sdcard, camera, accelerometer, gyroscope, i2c, wlan, ble	AW88298/ES7210/BMI270 wired; camera stub
M5Stack Tab5 (ILI9881C)	fbdisplay/m5stack_tab5_ili9881c	touch	audio_in, audio_out, sdcard, camera, i2c, wlan, ble	ES8388/ES7210 wired; camera stub
M5Stack Tab5 (ST7123)	fbdisplay/m5stack_tab5_st7123	touch	audio_in, audio_out, sdcard, camera, i2c, wlan, ble	same
LILYGO T-Display-S3	busdisplay/i80/t-display-s3	—	battery, wlan, ble
LILYGO T-Display-S3 Pro	busdisplay/spi/t-display-s3-pro	touch	sdcard, battery, wlan, ble
LILYGO T-QT Pro	busdisplay/spi/t-qt-pro	—	battery, wlan, ble
LILYGO T-Dongle-S3	busdisplay/spi/t-dongle-s3	—	pixels, wlan, ble
Adafruit MatrixPortal M4	fbdisplay/matrixportal_m4_64x32	—	accelerometer, i2c	HUB75 is display_drv
Adafruit MatrixPortal S3	fbdisplay/matrixportal_s3_64x64	—	accelerometer, i2c, wlan, ble
BPI-Centi-S3	busdisplay/i80/bpi-centi-s3	encoder	wlan, ble
WT32-SC01 Plus	busdisplay/i80/wt32sc01-plus	touch	sdcard, wlan, ble
ESP32-WROVER-E ST7789 + joystick	busdisplay/spi/esp32_wrover_e_st7789_joystick	joystick	wlan
PiTFT ILI9341 FeatherWing	busdisplay/spi/pitft_ili9341_featherwing	touch	i2c	host-dependent STEMMA
Pico 2 + DVI Sock / PiCowbell HSTX	fbdisplay/pico2_dvi_sock_640x480	—	(empty)	Sock and PiCowbell share GP12–19
Pico 2 W + DVI Sock / PiCowbell HSTX	fbdisplay/pico2w_dvi_sock_640x480	—	wlan, ble	same HSTX pins + CYW43
Olimex RP2350pc	fbdisplay/olimex_rp2350pc_640x480	—	sdcard, led, i2c	onboard HDMI (HSTX); no adapter
SparkFun IoT RedBoard RP2350 + HSTX→DVI	fbdisplay/sparkfun_iot_redboard_rp2350_hstx_640x480	—	sdcard, led, i2c, wlan, ble	needs FPC + SparkFun HSTX→DVI breakout

---

MIP install

import mip
mip.install(
    "github:PyDevices/pydevices/board_configs/<path>"
)

Replace <path> with a directory from the tables (for example fbdisplay/esp32-p4-wifi6-touch-lcd-4b). Also install the PyDevices packages listed in that board’s package.json deps.

---

Notes

• Lazy roles listed in PERIPHERALS may still raise NotImplementedError until factories are filled — the set is the contract surface, not a completeness guarantee.
• bt (Classic) is omitted unless a product is known to expose BR/EDR.
• Light / ALS sensors have no contract role yet — omit from PERIPHERALS.
• Metro M7 and Nucleo-H743ZI2 rows are the host board plus the Adafruit TFT touch shield 1947; the shield carries the display and touch.
• Generic OLED breakouts and EyeSPI stacks are not enumerated here unless they expose meaningful non-display PERIPHERALS roles.